K300 не заряжается

[Layder]

Вообщем пришел ко мне с перемычками вместо стекляшки на зарядку-интерфейс.
Поставил сразу стекляшку. При выключеном телефоне и подключении БП в качестве зарядки - пытается запуститься, потребляет 280мА пару секунд, появляется заставка SE (почему-то с повышенным контрастом), перестает потреблять, выключается. При включеном состоянии - показывает зарядку, потребление также: появлется, потом пропадает. Заменены все по 2 раза(т.к. ставил с разборки): стекляшка, контроллер питания, транзитор-ключевик заядки, резистор 0,1 ома, 2 резитора по 0.50 ома (около батареи), процессор, тело прошито фуллом с GDFS, все так и осталось. Батареи разные пробовал. Само тело работает без проблем.
Есть идеи? Или в утиль?

p.s.
додумался посмотреть лог при старте, нашел это:

552 BATT: Battery type is UNKNOWN
557 BATT: Measurements are 2798 mV and 0.0 mA
557 BATT: Charge current (0.0 mA) based remaining capacity is 100.0%

средний контакт батареи идет на контроллер питания. а откуда процессор узнает о типе батареи? смотрел схему, пока ничего не нашел.
кому интересно, вот полный лог:

OS: core startup of System
OS: MM init and instruction cache setup
OS: Installing static device drivers
OS: Starting RTC
OS: current time Thu Jan 1 00:01:07 1970
OS: Starting HEAP
OS: Memscan found Flash @ 0x44000000 Size=0x2000000
OS: Memscan found RAM @ 0x4c000000 Size=0x800000
OS: Memscan found unknown area @ 0x50000000 Size=0x2000000
OS: Starting FAM
OS: Flash area base:0x44000000 size:0x2000000 driver:cfi params:
OS: Executable flash area base:0x44000000 size:0xf00000
OS: Executable flash area base:0x45000000 size:0x200000
OS: MMU and data cache setup
FS: *** This is SEMC FS ***
FS: Server processes started.
FSFLASH: CPU is ARM 926, revision 3, architecture 6
FSFLASH: Inst Cache size is 16.00 Kb, 4-way, 32 bytes/line.
FSFLASH: Data Cache size is 8.00 Kb, 4-way, 32 bytes/line.
FSFLASH: NOR Flash device @ [0x44000000-0x45FFFFFF] 32768 Kb
FSFLASH: Vendor (0x20): ST
FSFLASH: Device ID: 0x880D
FSFLASH: Write Buffer Size: 64 bytes
FSFLASH: Erase region [0x44000000-0x45FDFFFF] has an erase block size of 128 Kb
FSFLASH: Erase region [0x45FE0000-0x45FFFFFF] has an erase block size of 32 Kb
FSFLASH: Write processes started, pid = 0x10025.
FSFLASH: Erase processes started, pid = 0x10026.
FSFLASH: Logical flash block size is 256 Kb
FSFLASH: File system flash segment 0 located in NOR @ [0x44D00000,0x44EFFFFF] (2048 Kb)
FSFLASH: File system flash segment 1 located in NOR @ [0x45000000,0x45FFFFFF] (16384 Kb)
FSFLASH: Pack Process started, pid = 0x10027.
MALL: **** NEW MAXIMUM XRAM HEAP USAGE: 1024 bytes requested in total ****
FSFLASH: 72 flash block(s) available (out of 72)
FSFLASH: Number of AVAILABLE file system blocks: 18104
FSFLASH: Number of USED file system blocks: 4198
FSFLASH: Number of DIRTY file system blocks: 138
FSFLASH: Number of CLEAN file system blocks: 14024
FSFLASH: Number of BAD file system blocks: 0
FS: Mounting file system partition /
FS: Mounting file system partition /tpa/system/bg_images/cache
FS: Mounting file system partition /ifs
FS: Mounting file system partition /system
FS: Mounting file system partition /smsdata
MALL: **** NEW MAXIMUM XRAM HEAP USAGE: 2048 bytes requested in total ****
BuildInfo: Label: <BAS_CORA_CRH109497_R5N_050524_0831> Variant: <cxc1328697_G200_PHONE_KRISTINA>
BuildInfo: Generated: 2005-05-24 09:08 by EMLDEHS
Product : <K300 series> Version: 0001
HW Setup : Marita Compact (Id:0x8000) IRDA: B004 BT: C002 RS232: A004
Vendor : <Sony Ericsson> PNP: SER USB: 0FCE BT: 0000
Prototype start process started!
MPH NullState
RLC: RLC_LLC
RLC: RLC_IDLE_REQ = 7385
RLC: RLC_GMM_DATA_REQ = 7386
RLC: RLC_DATA_REQ = 7387
RLC: RLC_UNITDATA_REQ = 7388
RLC: RLC_RLC_DATA_REQ = 7389
RLC: RLC_RLC_UNITDATA_REQ = 7390
RLC: RLC_DATA_RSP = 7391
RLC: LLC_RLC
RLC: RLC_DATA_CNF = 7395
RLC: RLC_DATA_IND = 7396
RLC: RLC_STATUS_IND = 7397
RLC: RR_RLC
RLC: RR_TBF_ESTABLISH_REQ = 6910
RLC: RR_UPLINK_TBF_RELEASE_REQ = 6912
RLC: RR_DOWNLINK_TBF_RELEASE_REQ = 6913
RLC: RR_TBF_RELEASE_RSP = 6914
RLC: RR_DOWNLINK_ACK_NACK_REQ = 6915
RLC: RLC_RR
RLC: RR_TBF_ESTABLISH_CNF = 6920
RLC: RR_UPLINK_TBF_RELEASE_CNF = 6922
RLC: RR_DOWNLINK_TBF_RELEASE_CNF = 6923
RLC: RR_TBF_ESTABLISH_IND = 6921
RLC: RR_TBF_RELEASE_IND = 6924
RLC: RR_UPLINK_ACK_NACK_IND = 6925
RLC: PH_RLC
RLC: PH_RLC_DATA_REQ = 7250
RLC: PH_RLC_DATA_RELEASE_REQ = 7252
RLC: PH_RLC_CONTROL_REQ = 7253
RLC: PH_RLC_CONTROL_CONTROL_0_PDCH_REQ = 7255
RLC: PH_RLC_CONTROL_CONTROL_1_PDCH_REQ = 7256
RLC: PH_RLC_CONTROL_CONTROL_2_PDCH_REQ = 7257
RLC: PH_RLC_CONTROL_CONTROL_3_PDCH_REQ = 7258
RLC: PH_RLC_CONTROL_CONTROL_4_PDCH_REQ = 7259
RLC: PH_RLC_CONTROL_CONTROL_5_PDCH_REQ = 7260
RLC: PH_RLC_CONTROL_DATA_0_PDCH_REQ = 7261
RLC: PH_RLC_CONTROL_DATA_1_PDCH_REQ = 7262
RLC: PH_RLC_CONTROL_DATA_2_PDCH_REQ = 7263
RLC: PH_RLC_CONTROL_DATA_3_PDCH_REQ = 7264
RLC: PH_RLC_CONTROL_DATA_4_PDCH_REQ = 7265
RLC: PH_RLC_CONTROL_DATA_5_PDCH_REQ = 7266
RLC: PH_RLC_CONTROL_CONTROL_0_PDTCH_PDCH_REQ = 7267
RLC: PH_RLC_CONTROL_CONTROL_1_PDTCH_PDCH_REQ = 7268
RLC: PH_RLC_CONTROL_CONTROL_2_PDTCH_PDCH_REQ = 7269
RLC: PH_RLC_CONTROL_CONTROL_3_PDTCH_PDCH_REQ = 7270
RLC: PH_RLC_CONTROL_CONTROL_4_PDTCH_PDCH_REQ = 7271
RLC: PH_RLC_CONTROL_CONTROL_5_PDTCH_PDCH_REQ = 7272
RLC: PH_RLC_CONTROL_DATA_0_PDTCH_PDCH_REQ = 7273
RLC: PH_RLC_CONTROL_DATA_1_PDTCH_PDCH_REQ = 7274
RLC: PH_RLC_CONTROL_DATA_2_PDTCH_PDCH_REQ = 7275
RLC: PH_RLC_CONTROL_DATA_3_PDTCH_PDCH_REQ = 7276
RLC: PH_RLC_CONTROL_DATA_4_PDTCH_PDCH_REQ = 7277
RLC: PH_RLC_CONTROL_DATA_5_PDTCH_PDCH_REQ = 7278
RLC: PH_RLC_RELEASE_REQ = 7279
RLC: RLC_PH
RLC: PH_RLC_DATA_CNF = 7290
RLC: PH_RLC_DATA_IND = 7291
RLC: PH_RLC_DATA_RTS_IND = 7292
RLC: PH_RLC_DATA_RELEASE_CNF = 7293
RLC: PH_RLC_CONNECT_IND = 7294
RLC: PH_RLC_CONTROL_CNF = 7295
RLC: PH_RLC_CONTROL_IND = 7296
RLC: PH_RLC_RELEASE_CNF = 7297
RLC: RLC_TIMER
RLC: RLC_TIMER_T3164 = 7465
RLC: RLC_TIMER_T3166 = 7466
RLC: RLC_TIMER_T3180 = 7467
RLC: RLC_TIMER_T3182 = 7468
RLC: RLC_TIMER_T3190 = 7469
RLC: RLC_TIMER_T3192 = 7472
RLC_UL: S I
RR: PID 65596
RR: TIMER_PRIM 7582
RR: MPH_RR_PRIM 6720
RR: RR_MPH_PRIM 6770
RR: RR_RLC_PRIM 6910
RR: RLC_RR_PRIM 6920
RR: PH_MPH_PRIM 7010
RR: MPH_PH_PRIM 7080
RR: PH_RLC_PRIM 7250
RR: RLC_PH_PRIM 7290
LLC: PID 65600
LLC: <SMS 3822
LLC: >SMS 3833
LLC: <SNDCP 7340 7348
LLC 1: state 0
LLC 3: state 0
LLC 5: state 0
LLC 7: state 0
LLC 9: state 0
LLC 11: state 0
RLC_DL: S ILLDebug_Init: LLDEBUG cable detected
ACB/Debug driver: LLDEBUG cable detected
ACB/Debug driver: Error PD_GPIO_InterruptUnsubscribe failed
### Print Server: Requesting DebugMux channel...
141 ### Print Server: Started OK
142 Prototype Start Process [File System Version Control]: Type OK (Kristina)
[142 Prototype Start Process [File System Version Control]: Version OK (P5T)
144 RLink: RLINK_PH
R
144 RLink: PH_RLINK_CONNECT_IND = 6672
144 RLink: PH_RLINK_DISCONNECT_IND = 6673
144 RLink: PH_RLINK_RTS_IND = 6670
144 RLink: PH_RLINK_DATA_IND = 6671
144
RLC: PH_RLINK
144 RLink: PH_RLINK_DATA_REQ = 6660
144
RLink: RLINK_RLP
144 RLink: RLINK_RLP_RTS_IND = 4990
144 RLink: RLINK_RLP_DATA_IND = 4994
144
RLC: RLP_RLINK
144 RLink: RLINK_RLP_DATA_REQ = 4995
144 RLink: RLINK_RLP_DTX_REQ = 4996
144
RLC: RLINK_RR
144 RLC: RR_CHANNEL_MODE_INFO_IND = 42861
145 RLC: RR_CHANNEL_MODE_MODIFY_IND = 42862
145 RLink: State Idlesysctrl] Initializing Interactive Debug support.
147 RH: Activate on LRRAT = 0
147 RH state: Inactiveational Rose RealTime C Target Run Time System
147 Release 6.50.C.00 (-Cl,G0,-L,+Me,-O)
147 Copyright (c) 1993-2003 Rational Software
148 SM: Initiated; ProcessID = 65652 !MM: reset TMSI
149 MM: No valid GSM keys
149 MM: No valid WCDMA keys
149 MM: TVP Probe P_UAS_CAS_MM_Status Error
149 MM: state 0
149 MM: TVP Probe P_UAS_CAS_MM_Status ErrorGMM: ResetSIM_Data
150 GMM: No valid GSM-GPRS keys
150 GMM: No valid WCDMA keys
150 LLC 1: Unexpected signal #7417* CC1 state 0
151 * CC2 state 0
151 * CC3 state 0
151 * CC4 state 0
151 * CC5 state 0
151 * CC6 state 0
151 * CC7 state 0
151 DRM: DRM_Process started
156 Assert Failure in .\cxc1328697_G200_PHONE_KRISTINA\IAR-ARM7\inc\dispdrv_phys_pdi.c(980)
158 MALL: **** NEW MAXIMUM XRAM HEAP USAGE: 2296 bytes requested in total ****
160 SS: State Idle @
160 CallMeter started
160 SMC_MO_1 (65627) state 4
160 SMC_MO_2 (65628) state 4
160 SMC_MT (65629) state 4
160 SMR_MO state 3
160 SMR_MT state 3
160 GDFS_SRV State 1-ClosedAM: MODULE_INIT
163 [sysctrl] Enabling UICC refresh task.
163 R2BA010 prgCXC125978_EU_1_KR
163 [SIM] State Changed: SIM_STATE_NULL, Appl: 0, Ref: 0
171 GDFS: Format version 1
173 GDFS Log[0] <- Phys[0] 56098 bytes left. Erased 0 times
175 GDFS Log[1] <- Phys[1] 62790 bytes left. Erased 0 times
178 GDFS Log[2] <- Phys[2] 18537 bytes left. Erased 0 times
180 GDFS Log[3] <- Phys[3] 105538 bytes left. Erased 0 times
180 GDFS Log[4] <- Phys[4] 106367 bytes left. Erased 0 times
181 GDFS Log[5] <- Phys[5] 107273 bytes left. Erased 0 times
181 GDFS Log[6] <- Phys[6] 131060 bytes left. Erased 0 times
183 GDFS_SRV State 2-Opening
184 CC: speech ver config 2 0 1 15 15
184 CC: TTY mode = 0
184 * CC0 state 0
185 MPH: PacketChannels activated
185 RR Multislot class GPRS = 8
185 RR state 0
185 MS_TYPE = MS_EGSM900_DCS1800_PCS1900
185 MPH:SelectedModeIndex=1
186 MPH_GD_Info.SensitivityLimit_dBm[BAND_GSM900_OR_EGSM900] = -107
186 ETX OK
186 MPH_GD_Info.SensitivityLimit_dBm[BAND_DCS1800] = -107
187 MPH_GD_Info.SensitivityLimit_dBm[BAND_PCS1900] = -107
187 MPH_GD_Info.SensitivityLimit_dBm[BAND_GSM850] = -107
187 MPH_GD_Info.MinNrOfIdentifiedCellsToSkipWeakCells = 0
189 MMM IMEI = 359986-00-822369-0, IMEI_SVN = 22
189 MMM EqPLMN List read from GDFS, nbr=1, 257 2
189 MMM: TVP Probe P_UAS_CAS_PLMN_List Error
189 MMM state 0
189 MMM MM_SIM_DATA_SET_REQ
192 DebugMux[IMEI] Length=8, TypeOfID=2, OddEven=1, Digits: 3 5 9 9 8 6 0 0 8
195 [lockctrl] SimLock : NOT OK, PhoneLock : NOT OK, Sim Active : NOT ACTIVE
197 IrDA_lap_rec.c: IrLAP process ready !
197 IrDA_lmp_rec.c: IrLMP process ready !
197 MMM MS_OperationMode=0
197 CCS: Idle
197 SL: SIGID_INTERVAL_START_MOD_NS_CAS = 3660
197 SL: ProcessID = 10055
198 SL: CFG_DISABLE_SECURITY_HANDLING is NOT! defined
198 SL: DUAL_RAT_SUPPORT is NOT! defined
198 SL state 0
198 SL<-EVENT_SIM_STATE_CHANGED in State 0 from 100ac
198 SL: Not active
198 SL new SIM handle=0RLP: process started
198 L2RCOP: process started
198 RLP: state changed to 'S0_ADMandDetached'
198 L2RCOP: state changed to 'Initial'
198 Load Module Starter: Hunt for Program Manager failedACM: Starting Application Side.
201 [sysctrl] start-up cause : Charger Connected
201 [sysctrl] System mode changed from SHUTDOWN/INITIATING to CHARGING/ALARM
201 [sysctrl] System Start-Up is complete
201 [lockctrl] SimLock : NOT OK, PhoneLock : NOT OK, Sim Active : NOT ACTIVE
201 [lockctrl] SimLock : OK, PhoneLock : NOT OK, Sim Active : NOT ACTIVE
201 [lockctrl] SimLock : OK, PhoneLock : OK, Sim Active : NOT ACTIVE
201 [sysctrl] Normal Voltage ind. received from SysPwr
202 [SIM_FILE_UTIL] FCP Cache Size 80AT process: Awake and AT your service!
212 ###Downloading DSP for first time after startup of phone!###
214 DSPIF_INT Exception: MPORTIF Soft reset
214 DSPIF_INT Exception: MPORTIF Soft reset
214 [ICC] Reader Voltage:OFF
214 [SIM-RDR] Fi: 1 Di: 1 Div1: 0 Div2: 0
215 [ICC] Reader Voltage:1V8
218 GVI:ReadyACM.StartMain: Starting First App. id=1...
223 DSPIF_INT Exception: MPORTIF Soft reset
223 DSPIF_INT Exception: MPORTIF Soft reset
223 ACM.StartMain: Start of First App ok.
223 AM: MODULE_INIT_READY
223
223
223 ******************************************
223 * Sony Ericsson Mobile Communications AB *
223 * Copyright 2003 *
223 ******************************************
223 * R2BA010 prgCXC125978_EU_1_KR *
223 ******************************************
224
224
224 AAM: Start initializing persistent data.
224 (OBEX/obex_session.c line: 2224) OBEX Started.
225 RTP_Ctrl started
225 MALL: **** NEW MAXIMUM XRAM HEAP USAGE: 2552 bytes requested in total ****
227 ## DSP VersionIdentity: "Marita Compact DSP midi_pcm_asr CNH1600219_R2L002______ 18Feb2005_13:44:18"
227 MALL: **** NEW MAXIMUM XRAM HEAP USAGE: 3576 bytes requested in total ****
228 MALL: **** NEW MAXIMUM XRAM HEAP USAGE: 4600 bytes requested in total ****
238 [ICC] Reader Voltage:OFF
240 MALL: **** NEW MAXIMUM XRAM HEAP USAGE: 5642 bytes requested in total ****
250 [SIM-RDR] Fi: 1 Di: 1 Div1: 0 Div2: 0
250 [ICC] Reader Voltage:3V
272 [ICC] Reader Voltage:OFF
272 [SIM] WARNING - Destruction of Application Parameters
272 [SIM_FILE_UTIL] Used Cache Records 0
272 [SIM_FILE_UTIL] Max Cache Records 80
272 [SIM] WARNING - Destruction of Card Parameters
272 [SIM] State Changed: SIM_STATE_POWER_OFF, Appl: 0, Ref: 0
272 [lockctrl] SimLock : OK, PhoneLock : OK, Sim Active : NOT ACTIVE
272 SL<-EVENT_SIM_STATE_CHANGED in State 0 from 100ac
273 SL: Not active
273 SL new SIM handle=0
275 MALL: **** NEW MAXIMUM XRAM HEAP USAGE: 6106 bytes requested in total ****
276 MALL: **** NEW MAXIMUM XRAM HEAP USAGE: 6882 bytes requested in total ****
282 MALL: **** NEW MAXIMUM XRAM HEAP USAGE: 7906 bytes requested in total ****AAM: Done initializing persistent data.
339 MMPROT[RTSP]: RTSP Process Started
340 MALL: **** NEW MAXIMUM XRAM HEAP USAGE: 8930 bytes requested in total ****
355
357 MSG: msgmain.c: State 255OS: Starting ose_memory_mgr
358 OS: core startup complete!
358 GDFS_WR State 1-Closed
358 GDFS_WR Start check
361 MALL: **** NEW MAXIMUM XRAM HEAP USAGE: 9552 bytes requested in total ****GDFS_Wrapper: **** Up and running ****
362
362 MAPP: OSC charging
377 Watchdog: process up and running.
377 Watchdog: Crash SMS not activated
379 ***** Investigating Language Availability *****
380 MALL: **** NEW MAXIMUM XRAM HEAP USAGE: 10203 bytes requested in total ****
382 MALL: **** NEW MAXIMUM XRAM HEAP USAGE: 10853 bytes requested in total ****
385 MALL: **** NEW MAXIMUM XRAM HEAP USAGE: 11419 bytes requested in total ****
387 AUC_INFO: AC_SetAcousticProperties, /ifs/settings/acoustic/farfield_play.apf
390 EST: FS = Available, ROM = Unavailable
390 ENG: FS = Unavailable, ROM = Available
390 LAT: FS = Available, ROM = Unavailable
391 LIT: FS = Available, ROM = Unavailable
391 POL: FS = Available, ROM = Unavailable
391 RUS: FS = Available, ROM = Unavailable
391 UKR: FS = Available, ROM = Unavailable
391 ***********************************************
393 MALL: **** NEW MAXIMUM XRAM HEAP USAGE: 22855 bytes requested in total ****
393 Disp_CreateFont: Creating font 0
393 Disp_CreateFont: Creating font 1
394 Disp_CreateFont: Creating font 2
394 Disp_CreateFont: Creating font 10
394 Disp_CreateFont: Creating font 11
394 Disp_CreateFont: Creating font 12
395 Disp_CreateFont: Creating font 13
395 Disp_CreateFont: Creating font 15
396 *** Disp_SetDefaultGlyph: Font 15 failed to set default glyph!
396 SEMC DISPUTIL Line:1953 OPA_ErrorCode: Unknown ErrorCode
396 Disp_CreateFont: Creating font 16
396 Disp_CreateFont: Creating font 17
397 Disp_CreateFont: Creating font 18
397 Disp_CreateFont: Creating font 20
397 Disp_CreateFont: Creating font 31
397 Disp_CreateFont: Creating font 32
398 Disp_CreateFont: Creating font 33
398 Disp_CreateFont: Creating font 34
398 Disp_CreateFont: Creating font 47
399 Disp_CreateFont: Creating font 55
399 Disp_CreateFont: Creating font 54
406 ***** Investigating Input Features *****
406 Arabic: NO
406 China: NO
406 Hebrew: NO
406 T9: YES
406 Greek: NO
406 Cyrillic: NO
406 Thai: NO
406 Icelandic: NO
406 Ukrainian: NO
406 Hindi: NO
406 Bengali: NO
406 ****************************************
406 ***** Investigating Input Language Availability *****
406 Predictive state is: ON
406 Predictive default (cust) is: ON
407 ENG: allowed = YES, T9-FS = NO, T9-ROM = YES
407 POL: allowed = YES, T9-FS = YES, T9-ROM = NO
407 RUS: allowed = YES, T9-FS = YES, T9-ROM = NO
408 USE: allowed = YES, T9-FS = NO, T9-ROM = YES
408 UKR: allowed = YES, T9-FS = NO, T9-ROM = NO
408 ABC: allowed = YES, T9-FS = NO, T9-ROM = NO
408 123: allowed = YES, T9-FS = NO, T9-ROM = NO
408 *** (T9) ENG matches USE
408 *** Resolve ok (1), keeping ENG
408 ************************************************** ***
411 DRM Init OK
412 DRM_PRS_Process started
412 MALL: **** NEW MAXIMUM XRAM HEAP USAGE: 24406 bytes requested in total ****
418 SL<-REQUEST_VOICECALLVOLUME_SET in State 0 from 100ce
419 SL: Not active
473 MALL: **** NEW MAXIMUM XRAM HEAP USAGE: 25642 bytes requested in total ****
474 MALL: **** NEW MAXIMUM XRAM HEAP USAGE: 29288 bytes requested in total ****
474 MALL: **** NEW MAXIMUM XRAM HEAP USAGE: 33248 bytes requested in total ****
474 MALL: **** NEW MAXIMUM XRAM HEAP USAGE: 35161 bytes requested in total ****
475 MALL: **** NEW MAXIMUM XRAM HEAP USAGE: 37273 bytes requested in total ****
475 MALL: **** NEW MAXIMUM XRAM HEAP USAGE: 39385 bytes requested in total ****
476 MALL: **** NEW MAXIMUM XRAM HEAP USAGE: 41376 bytes requested in total ****
527 [StandbyBook:53] Created
530 ImageViewer_Animation: Can not start animation since no valid area to draw in is set!!
532 MALL: **** NEW MAXIMUM XRAM HEAP USAGE: 43450 bytes requested in total ****
533 [StandbyBook:53] Goto StandbyBook_StandbyPage
533 [InitBook:54] Created
533 [InitBook:54] Goto InitBook_StartUp_Page
533 [InitBook:54] Got focus
537 MALL: **** NEW MAXIMUM XRAM HEAP USAGE: 45734 bytes requested in total ****
537 ImageViewer_Animation: Can not start animation since no valid area to draw in is set!!
539 [InitBook:54] Goto InitBook_ChargingOnly_Page
539 [InitBook:54] Lost focus
539 [StandbyBook:53] Got focus
540 [StandbyBook:53] Goto StandbyBook_ChargingOnly_Page
540 MALL: **** NEW MAXIMUM XRAM HEAP USAGE: 48034 bytes requested in total ****
542 MALL: **** NEW MAXIMUM XRAM HEAP USAGE: 50462 bytes requested in total ****
542 MALL: **** NEW MAXIMUM XRAM HEAP USAGE: 56422 bytes requested in total ****
545 SL<-REQUEST_TTY_MODE_SET in State 0 from 100d3
545 SL: Not active
546 ***** Calling IAC_ServerASC_SetVolume *****
546 ***** RingVolume = 5 ****
546 ***** SUCCESS *****
552 BATT: Battery type is UNKNOWN
557 BATT: Measurements are 2798 mV and 0.0 mA
557 BATT: Charge current (0.0 mA) based remaining capacity is 100.0%
569
570 [StandbyBook:53] Goto StandbyBook_ShutDown_Page
577 [OnOffBook:55] Created
577 [StandbyBook:53] Lost focus
577 [OnOffBook:55] Got focus
577 [OnOffBook:55] Goto OnOffBook_ShuttingDownPage
620 AUC: Open Audio: ID: 1. Frequency: 3. Prio: 1 Channels: [0,1,0,1]
620 AUC: Open Audio: Open Channels 1, Freq: 3
624 DSPIF_INT Exception: MPORTIF Soft reset
624 DSPIF_INT Exception: MPORTIF Soft reset
626 DSPIF_INT Exception: MPORTIF Soft reset
626 DSPIF_INT Exception: MPORTIF Soft reset
634 DSPIF_INT Exception: MPORTIF Soft reset
634 DSPIF_INT Exception: MPORTIF Soft reset
638 ## DSP VersionIdentity: "Marita Compact DSP midi_pcm_asr CNH1600219_R2L002______ 18Feb2005_13:44:18"
650 [OnOffAnimationBook:56] Created
650 [OnOffBook:55] Lost focus
651 [OnOffAnimationBook:56] Got focus
663 [OnOffAnimationBook:56] Goto OnOffAnimation_ShowAnimation_Page
663 CreateGuiImageViewer is obsolete! Change to new gui_imageviewer interface instead...
813 AUC: Close Audio: ID: 1. Frequency: 3. Channels: [0,1,0,1]. SendEvent: 0
823 AUC: Close Audio: Open Channels 0, Freq: 0
951
951 WAP:Start (process id 0x10089)
951 WAP: File API Initiated
952 WAP: created task 0
953 WAP: fileMkDir(.../stk)
954 WAP: fileMkDir(.../stk/tmp)
955 WAP: created task 1
958 OAS: 0 Profile Roles active
958 changed to state 0
959 PBS Process started
959
959 PBS: Dispatch PHB_NO_ACCESS
1062 Crypto-capable module loaded as default.
1082 MSG: msgmain.c: State 0 changed to state 1
1082 MSG: msgmain.c: EVENT_SIM_STATE_CHANGED accepted
1082 MSG: msgmain.c: SIM_STATE NOT Active
1082 MSG: msgmain.c: EVENT_SIM_STATE_CHANGED accepted
1082 MSG: msgmain.c: SIM_STATE NOT Active
1226 Handle_Shell_Timeout: Time-out from non-existent timer: 4c71b25c - Ignored.
1228 Handle_Shell_Timeout: Time-out from non-existent timer: 4c71b25c - Ignored.
1310 BATT: Measurements are 3796 mV and -51.0 mA
1310 BATT: Compensated VBAT (3671 mV) based remaining capacity is 11.6%
1310 BATT: Average remaining capacity is 11.6%
1481 GDFS Free Blk 7 Ok
1481 GDFS_WR Check done
1481 GDFS_SRV State 3-Open
1502 GDFS_WR State 2-Open
1560 BATT: Measurements are 3806 mV and -51.0 mA
1560 BATT: Compensated VBAT (3681 mV) based remaining capacity is 13.0%
1560 BATT: Average remaining capacity is 12.3%
1810 BATT: Measurements are 3806 mV and -45.0 mA
1810 BATT: Compensated VBAT (3681 mV) based remaining capacity is 13.0%
1810 BATT: Average remaining capacity is 12.5%
1819 INTERNAL ERROR CDisplayManager_imp.c(311): 0x00000000
1819 SEMC DISPBASE Line:5116 OPA_ErrorCode: Unknown ErrorCodeSEMC_TimerProcess: Received signal to exit.
1829 SEMC_TimerProcess_: Send message to self to terminate.
1829 SEMC_TimerProcess_: All claimed resources now freed. Exiting.
1836 [sysctrl] System shut down
1836 AM:MODULE_SHUTDOWN
1837 AM:MODULE_SHUTDOWN_READY
1837
1838 GVI Heap:ERROR Delete local heap without freeing all memory diff 78 allocations
1838
1838
1838
1838 MSG: msgmain.c: UNEXPECTED PRIMITIVE 44985 RECEIVED
1839 MSG: msgmain.c: SHUTTING DOWN
1839 MSG: msgmain.c: SHUTDOWN COMPLETE
1839 [sysctrl] Deactivating Network Signalling
1839 SL<-R_REQ_NS_DEACTIVATE in State 0 from 1002e
1839 MMM state 17
1839 MM: IsMM_Connected=0
1839 MM: REG FAILED, Cause = DETACHED
1839 GMM<-GMM_DEACTIVATE_REQ
1839 GMM: TVP_GetTimerIndex no TVP timer
1839 GMM: New TLLI distributed to RR: 0xffffffff (255, 255, 255, 255)
1839 TLLI_PTMSI_New
1839 case1 UnassBoth
1840 GMM: Reset combined procedures
1840 GMM: REG FAILED, Cause = DETACHED
1840 MPH Off
1849 MMM state 0

[Viktor001]

Менять детальки наугад, очень непроизводительно. Многие из них можно проверить обычным китайским тестером. Резисторы уж всяко проще прозвонить, чем менять.
Попробуй начать с начала.
Часто попадается подгнившие контакты, и от этого повышеное сопротивление в цепи заряда. На подключение зарядного, телефон может реагировать, но зарядка не идёт, или через какоето время прекращается.
Прозвони от контактов зарядки на системном разъме, до конденсатора С2402 на плате. Плюс зарядки на плюс конденсатора должно показывать цепь сопротивлением ноль Ом. И минусовая цепь также.
Прозвони от плюса С2402 до плюса С2620 (он на плате не установлен, только контактные площадки). Это проверяем "стекляшку". При исправной, должно показывать 10-12 Ом.
Включи телефон, и подай от БП на вход зарядки 5 - 5,5 вольт. Если всё исправно, то телефон должен начать заряжаться, а амперметр должен показать ток около 500 мА. Можно поэкспериментировать с напряжением, подать чуть больше.
Если ток зарядки есть, но значительно меньше, возможно неисправна или "левая" АКБ. Проверить её в заведомо исправном телефоне, или подкинуть исправную АКБ.
Или же проблема со средним контактом АКБ в разъёме телефона. Его сначала прозвонить, относительно плюсового и минусового контактов. В обоих случаях, должно показывать примерно как при прозвонке диода.
Если показывает обрыв, в первую очередь посмотреть не оборвана ли пайка самих контактов. Причём, обрыв может появляться, только когда АКБ вставлена и давит на контакты. Далее прозвонить на плюс V2600 (он на плате не установлен). А дальше дорожка идёт внутрь платы и выныривает уже под контролером питания.
Если показывает КЗ или большую утечку на крайние контакты, то может быть убитый контролер питания. Или искать, где прогорела изоляция.
Посмотреть, нет ли окиси вокруг контактов в разъёме. И ещё, чуть выше контактов АКБ, на плате есть три круглых пятака. Обычно они заклеены плёнкой. Там тоже помотреть. Так как цепь контроля высокоомная (десятки килоом), то даже небольшая утечка по окиси, может всё испортить.
средний контакт батареи идет на контроллер питания. а откуда процессор узнает о типе батареи? смотрел схему, пока ничего не нашел.
Микрухи между собой переговариваются по цифровой шине.

[Layder]

Viktor001, спасибо за столько широкий ответ, но почти все было просмотрено. средний контакт акб в режиме диода прозванивается, значит сигнал от АКБ до контроллера доходит, а до процессора - нет. а АКБ менялась на другую.
смущает то, что транзистор открывается на заряд, потом телефон ток зарядки меряет и отключает зарядку.

[vth]

Покажите лог телефона во включенном состоянии, чтобы он говорил о состоянии батареи не два раза, а чуть больше. Там он сообщит о температуре батареи и платы, самое интересное там.
Кроме того "доходит до контроллера и не доходит до процессора" в корне не верно.
Контроллер весьма "умная" микросхема, она общается с батареей, меряет температуру платы, обслуживает ЦАПы/АЦПы и др. пр. Процессор же общается с контроллером по паре цифровых шин.
Так что тут либо всё доходит, либо ничего.
Раньше на к500/к700/к300 любил коротить шлейф камеры на контрольную точку среднего контакта. Но случай вероятно не ваш.
Надо посмотреть температуру.

[Arni]

Вообщем пришел ко мне с перемычками вместо стекляшки на зарядку-интерфейс.
Поставил сразу стекляшку.

А до замены проводка на стекляшку вел себя так же?

[Viktor001]

средний контакт акб в режиме диода прозванивается, значит сигнал от АКБ до контроллера доходит, а до процессора - нет. а АКБ менялась на другую.
смущает то, что транзистор открывается на заряд, потом телефон ток зарядки меряет и отключает зарядку.
Транзистор (v2610) не сам по себе открывается. Его открывает контролер питания.
Сам транзистор можно проверить не выпаивая:
АКБ снять. На вход зарядки подать 4 вольта. Мерим на контактах разъёма АКБ. Там не должно быть напряжения, или совсем небольшой потенциал.
Коротим затвор (4 ногу) транзистора на массу. Для чистоты эксперимента, коротить на массу лучше не напрямую, а через резистор, сопротивлением в несколько килоом. На контактах АКБ должно появиться напряжение, которое подано на вход зарядки. Если всё так, то транзистор исправен, и выход КП в порядке (во всяком случае не пробит). Есть ли цепь между затвором транзистора и выходом КП - звоним 4 ногу транзистора, относительно массы, должно вызваниваться как диод. Можно ничего отпаивая (т.к. транзистор с изолированым затвором и на результаты измерения не повлияет), или для полной уверености, можно отпаять только транзистор. Полностью проверить исправность КП - наверное только заменой.
В среднем контакте, который в самом АКБ, никакой логики нет. Туда подключен терморезистор, вторым концом он сидит на минусе. По сопротивлению этого терморезистора, телефон определяет тип АКБ, и его температуру. В BST-35 терморезистор 110 кОм. И проверять нужно с оригинальным АКБ. В китайские могут поставить резистор тот что есть под руками, а не тот что нужен. И телефон вообще может отказаться заряжаться. Но всё равно можно обмануть. Заклеиваешь средний контакт. Телефон будет ругаться "Неизвестный аккумулятор", но заряжать будет. Правда ток зарядки будет ниже, примерно 50 процентов от номинального.
Если у тебя и с заклееным контактом не заряжает. Значит чтото очень не нравится в цепи среднего контакта. Если цепь до КП звонится, и явного коротыша на плюс и минус нет, то остаётся только утечка. Если на плате окислений не видать, отпаяй разъём АКБ, может под ним окисление. Или в самом разъёме пластмаса прогорела.

[Layder]

А до замены проводка на стекляшку вел себя так же?

а хез. принесли - не заряжается. а там около стекляшки флюсом корявым все залито и на соплях запаяно было, поэтому сразу и переделывал.

Если у тебя и с заклееным контактом не заряжает. Значит что-то очень не нравится в цепи среднего контакта.
вчера промыл в ванночке, без толку.
обрезал дорожку до разъема батареи около незапаянного варистора - тоже не заряжается.

В BST-35 терморезистор 110 кОм.

батарея оригинал моя б.у., померял резистор - 120кОм


полный лог после еще одной прошивки. к конце - передернул кабель, чтобы инициировать подключенение задяного
UFxBoot V2.2 (c) SarasSoft 2003. Id: 62 CF 1 10
UFS_USB V2.8 (c) SarasSoft 2007. S/n:


OS: core startup of System
OS: MM init and instruction cache setup
OS: Installing static device drivers
OS: Starting RTC
OS: current time Thu Jan 1 00:17:20 1970
OS: Starting HEAP
OS: Memscan found Flash @ 0x44000000 Size=0x2000000
OS: Memscan found RAM @ 0x4c000000 Size=0x800000
OS: Memscan found unknown area @ 0x50000000 Size=0x2000000
OS: Starting FAM
OS: Flash area base:0x44000000 size:0x2000000 driver:cfi params:
OS: Executable flash area base:0x44000000 size:0xf00000
OS: Executable flash area base:0x45000000 size:0x200000
OS: MMU and data cache setup
FS: *** This is SEMC FS ***
FS: Server processes started.
FSFLASH: CPU is ARM 926, revision 3, architecture 6
FSFLASH: Inst Cache size is 16.00 Kb, 4-way, 32 bytes/line.
FSFLASH: Data Cache size is 8.00 Kb, 4-way, 32 bytes/line.
FSFLASH: NOR Flash device @ [0x44000000-0x45FFFFFF] 32768 Kb
FSFLASH: Vendor (0x20): ST
FSFLASH: Device ID: 0x880D
FSFLASH: Write Buffer Size: 64 bytes
FSFLASH: Erase region [0x44000000-0x45FDFFFF] has an erase block size of 128 Kb
FSFLASH: Erase region [0x45FE0000-0x45FFFFFF] has an erase block size of 32 Kb
FSFLASH: Write processes started, pid = 0x10025.
FSFLASH: Erase processes started, pid = 0x10026.
FSFLASH: Logical flash block size is 256 Kb
FSFLASH: File system flash segment 0 located in NOR @ [0x44D00000,0x44EFFFFF] (2048 Kb)
FSFLASH: File system flash segment 1 located in NOR @ [0x45000000,0x45FFFFFF] (16384 Kb)
FSFLASH: Pack Process started, pid = 0x10027.
MALL: **** NEW MAXIMUM XRAM HEAP USAGE: 1024 bytes requested in total ****
FSFLASH: 72 flash block(s) available (out of 72)
FSFLASH: Number of AVAILABLE file system blocks: 18104
FSFLASH: Number of USED file system blocks: 4978
FSFLASH: Number of DIRTY file system blocks: 642
FSFLASH: Number of CLEAN file system blocks: 755
FSFLASH: Number of BAD file system blocks: 0
FS: Mounting file system partition /
FSCK: Phone not properly shut down, running FSCK on partition /
FSCK: FSCK level is 1
MALL: **** NEW MAXIMUM XRAM HEAP USAGE: 2002 bytes requested in total ****
MALL: **** NEW MAXIMUM XRAM HEAP USAGE: 6402 bytes requested in total ****
MALL: **** NEW MAXIMUM XRAM HEAP USAGE: 8404 bytes requested in total ****
MALL: **** NEW MAXIMUM XRAM HEAP USAGE: 9428 bytes requested in total ****
MALL: **** NEW MAXIMUM XRAM HEAP USAGE: 10452 bytes requested in total ****
MALL: **** NEW MAXIMUM XRAM HEAP USAGE: 11604 bytes requested in total ****
FSCK: Checking Inodes Pass 1
FSCK: Directory Check Pass 1
FSCK: Re-creating Free List
MALL: **** NEW MAXIMUM XRAM HEAP USAGE: 12546 bytes requested in total ****
MALL: **** NEW MAXIMUM XRAM HEAP USAGE: 13570 bytes requested in total ****
MALL: **** NEW MAXIMUM XRAM HEAP USAGE: 14594 bytes requested in total ****
MALL: **** NEW MAXIMUM XRAM HEAP USAGE: 15618 bytes requested in total ****
MALL: **** NEW MAXIMUM XRAM HEAP USAGE: 16642 bytes requested in total ****
MALL: **** NEW MAXIMUM XRAM HEAP USAGE: 17666 bytes requested in total ****
MALL: **** NEW MAXIMUM XRAM HEAP USAGE: 18690 bytes requested in total ****
MALL: **** NEW MAXIMUM XRAM HEAP USAGE: 19714 bytes requested in total ****
MALL: **** NEW MAXIMUM XRAM HEAP USAGE: 20738 bytes requested in total ****
MALL: **** NEW MAXIMUM XRAM HEAP USAGE: 22786 bytes requested in total ****
MALL: **** NEW MAXIMUM XRAM HEAP USAGE: 24834 bytes requested in total ****
MALL: **** NEW MAXIMUM XRAM HEAP USAGE: 26882 bytes requested in total ****
MALL: **** NEW MAXIMUM XRAM HEAP USAGE: 28930 bytes requested in total ****
MALL: **** NEW MAXIMUM XRAM HEAP USAGE: 30978 bytes requested in total ****
MALL: **** NEW MAXIMUM XRAM HEAP USAGE: 33026 bytes requested in total ****
MALL: **** NEW MAXIMUM XRAM HEAP USAGE: 35074 bytes requested in total ****
MALL: **** NEW MAXIMUM XRAM HEAP USAGE: 37122 bytes requested in total ****
FSCK: Checking 2200 Inodes Pass 2
FSCK: Directory Check Pass 2
MALL: **** NEW MAXIMUM XRAM HEAP USAGE: 39426 bytes requested in total ****
FSCK: File System Size: 15706
FSCK: Number of Free Data Blocks: 11185
FSCK: Number of Used Data Blocks: 4521
FSCK: Number of Free Inodes: 1723
FSCK: Number of Free Links: 1724
FSCK: Creating RamDir entries.
MALL: **** NEW MAXIMUM XRAM HEAP USAGE: 42242 bytes requested in total ****
MALL: **** NEW MAXIMUM XRAM HEAP USAGE: 51458 bytes requested in total ****
MALL: **** NEW MAXIMUM XRAM HEAP USAGE: 67074 bytes requested in total ****
MALL: **** NEW MAXIMUM XRAM HEAP USAGE: 102402 bytes requested in total ****
FSCK: Done
FS: Mounting file system partition /tpa/system/bg_images/cache
FS: Mounting file system partition /ifs
FSCK: Phone not properly shut down, running FSCK on partition /ifs
FSCK: FSCK level is 1
FSCK: Checking Inodes Pass 1
FSCK: Directory Check Pass 1
FSCK: Re-creating Free List
FSCK: Checking 304 Inodes Pass 2
FSCK: Directory Check Pass 2
FSCK: File System Size: 456
FSCK: Number of Free Data Blocks: 198
FSCK: Number of Used Data Blocks: 258
FSCK: Number of Free Inodes: 136
FSCK: Number of Free Links: 138
FSCK: Creating RamDir entries.
FSCK: Done
FS: Mounting file system partition /system
FSCK: Phone not properly shut down, running FSCK on partition /system
FSCK: FSCK level is 1
FSCK: Checking Inodes Pass 1
FSCK: Directory Check Pass 1
FSCK: Re-creating Free List
FSCK: Checking 200 Inodes Pass 2
FSCK: Directory Check Pass 2
FSCK: File System Size: 470
FSCK: Number of Free Data Blocks: 460
FSCK: Number of Used Data Blocks: 10
FSCK: Number of Free Inodes: 181
FSCK: Number of Free Links: 182
FSCK: Creating RamDir entries.
FSCK: Done
FS: Mounting file system partition /smsdata
BuildInfo: Label: <BAS_CORA_CRH109497_R5N_050524_0831> Variant: <cxc1328697_G200_PHONE_KRISTINA>
BuildInfo: Generated: 2005-05-24 09:08 by EMLDEHS
Product : <K300 series> Version: 0001
HW Setup : Marita Compact (Id:0x8000) IRDA: B004 BT: C002 RS232: A004
Vendor : <Sony Ericsson> PNP: SER USB: 0FCE BT: 0000
Prototype start process started!
MPH NullState
RLC: RLC_LLC
RLC: RLC_IDLE_REQ = 7385
RLC: RLC_GMM_DATA_REQ = 7386
RLC: RLC_DATA_REQ = 7387
RLC: RLC_UNITDATA_REQ = 7388
RLC: RLC_RLC_DATA_REQ = 7389
RLC: RLC_RLC_UNITDATA_REQ = 7390
RLC: RLC_DATA_RSP = 7391
RLC: LLC_RLC
RLC: RLC_DATA_CNF = 7395
RLC: RLC_DATA_IND = 7396
RLC: RLC_STATUS_IND = 7397
RLC: RR_RLC
RLC: RR_TBF_ESTABLISH_REQ = 6910
RLC: RR_UPLINK_TBF_RELEASE_REQ = 6912
RLC: RR_DOWNLINK_TBF_RELEASE_REQ = 6913
RLC: RR_TBF_RELEASE_RSP = 6914
RLC: RR_DOWNLINK_ACK_NACK_REQ = 6915
RLC: RLC_RR
RLC: RR_TBF_ESTABLISH_CNF = 6920
RLC: RR_UPLINK_TBF_RELEASE_CNF = 6922
RLC: RR_DOWNLINK_TBF_RELEASE_CNF = 6923
RLC: RR_TBF_ESTABLISH_IND = 6921
RLC: RR_TBF_RELEASE_IND = 6924
RLC: RR_UPLINK_ACK_NACK_IND = 6925
RLC: PH_RLC
RLC: PH_RLC_DATA_REQ = 7250
RLC: PH_RLC_DATA_RELEASE_REQ = 7252
RLC: PH_RLC_CONTROL_REQ = 7253
RLC: PH_RLC_CONTROL_CONTROL_0_PDCH_REQ = 7255
RLC: PH_RLC_CONTROL_CONTROL_1_PDCH_REQ = 7256
RLC: PH_RLC_CONTROL_CONTROL_2_PDCH_REQ = 7257
RLC: PH_RLC_CONTROL_CONTROL_3_PDCH_REQ = 7258
RLC: PH_RLC_CONTROL_CONTROL_4_PDCH_REQ = 7259
RLC: PH_RLC_CONTROL_CONTROL_5_PDCH_REQ = 7260
RLC: PH_RLC_CONTROL_DATA_0_PDCH_REQ = 7261
RLC: PH_RLC_CONTROL_DATA_1_PDCH_REQ = 7262
RLC: PH_RLC_CONTROL_DATA_2_PDCH_REQ = 7263
RLC: PH_RLC_CONTROL_DATA_3_PDCH_REQ = 7264
RLC: PH_RLC_CONTROL_DATA_4_PDCH_REQ = 7265
RLC: PH_RLC_CONTROL_DATA_5_PDCH_REQ = 7266
RLC: PH_RLC_CONTROL_CONTROL_0_PDTCH_PDCH_REQ = 7267
RLC: PH_RLC_CONTROL_CONTROL_1_PDTCH_PDCH_REQ = 7268
RLC: PH_RLC_CONTROL_CONTROL_2_PDTCH_PDCH_REQ = 7269
RLC: PH_RLC_CONTROL_CONTROL_3_PDTCH_PDCH_REQ = 7270
RLC: PH_RLC_CONTROL_CONTROL_4_PDTCH_PDCH_REQ = 7271
RLC: PH_RLC_CONTROL_CONTROL_5_PDTCH_PDCH_REQ = 7272
RLC: PH_RLC_CONTROL_DATA_0_PDTCH_PDCH_REQ = 7273
RLC: PH_RLC_CONTROL_DATA_1_PDTCH_PDCH_REQ = 7274
RLC: PH_RLC_CONTROL_DATA_2_PDTCH_PDCH_REQ = 7275
RLC: PH_RLC_CONTROL_DATA_3_PDTCH_PDCH_REQ = 7276
RLC: PH_RLC_CONTROL_DATA_4_PDTCH_PDCH_REQ = 7277
RLC: PH_RLC_CONTROL_DATA_5_PDTCH_PDCH_REQ = 7278
RLC: PH_RLC_RELEASE_REQ = 7279
RLC: RLC_PH
RLC: PH_RLC_DATA_CNF = 7290
RLC: PH_RLC_DATA_IND = 7291
RLC: PH_RLC_DATA_RTS_IND = 7292
RLC: PH_RLC_DATA_RELEASE_CNF = 7293
RLC: PH_RLC_CONNECT_IND = 7294
RLC: PH_RLC_CONTROL_CNF = 7295
RLC: PH_RLC_CONTROL_IND = 7296
RLC: PH_RLC_RELEASE_CNF = 7297
RLC: RLC_TIMER
RLC: RLC_TIMER_T3164 = 7465
RLC: RLC_TIMER_T3166 = 7466
RLC: RLC_TIMER_T3180 = 7467
RLC: RLC_TIMER_T3182 = 7468
RLC: RLC_TIMER_T3190 = 7469
RLC: RLC_TIMER_T3192 = 7472
RLC_UL: S I
RR: PID 65596
RR: TIMER_PRIM 7582
RR: MPH_RR_PRIM 6720
RR: RR_MPH_PRIM 6770
RR: RR_RLC_PRIM 6910
RR: RLC_RR_PRIM 6920
RR: PH_MPH_PRIM 7010
RR: MPH_PH_PRIM 7080
RR: PH_RLC_PRIM 7250
RR: RLC_PH_PRIM 7290
LLC: PID 65600
LLC: <SMS 3822
LLC: >SMS 3833
LLC: <SNDCP 7340 7348
LLC 1: state 0
LLC 3: state 0
LLC 5: state 0
LLC 7: state 0
LLC 9: state 0
LLC 11: state 0
RLC_DL: S ILLDebug_Init: LLDEBUG cable detected
ACB/Debug driver: LLDEBUG cable detected
ACB/Debug driver: Error PD_GPIO_InterruptUnsubscribe failed
### Print Server: Requesting DebugMux channel...
535 ### Print Server: Started OK
537 Prototype Start Process [File System Version Control]: Type OK (Kristina)
[537 Prototype Start Process [File System Version Control]: Version OK (P5T)
R538 RLink: RLINK_PH
538 RLink: PH_RLINK_CONNECT_IND = 6672
538 RLink: PH_RLINK_DISCONNECT_IND = 6673
538 RLink: PH_RLINK_RTS_IND = 6670
538 RLink: PH_RLINK_DATA_IND = 6671
538
RLC: PH_RLINK
538 RLink: PH_RLINK_DATA_REQ = 6660
538
RLink: RLINK_RLP
538 RLink: RLINK_RLP_RTS_IND = 4990
538 RLink: RLINK_RLP_DATA_IND = 4994
538
RLC: RLP_RLINK
538 RLink: RLINK_RLP_DATA_REQ = 4995
538 RLink: RLINK_RLP_DTX_REQ = 4996
538
RLC: RLINK_RR
538 RLC: RR_CHANNEL_MODE_INFO_IND = 42861
538 RLC: RR_CHANNEL_MODE_MODIFY_IND = 42862
539 RLink: State Idlesysctrl] Initializing Interactive Debug support.
539 RH: Activate on LRRAT = 0
539 RH state: Inactiveational Rose RealTime C Target Run Time System
539 Release 6.50.C.00 (-Cl,G0,-L,+Me,-O)
539 Copyright (c) 1993-2003 Rational Software
541 SM: Initiated; ProcessID = 65652 !MM: reset TMSI
541 MM: No valid GSM keys
542 MM: No valid WCDMA keys
542 MM: TVP Probe P_UAS_CAS_MM_Status Error
542 MM: state 0
542 MM: TVP Probe P_UAS_CAS_MM_Status ErrorGMM: ResetSIM_Data
543 GMM: No valid GSM-GPRS keys
543 GMM: No valid WCDMA keys
543 LLC 1: Unexpected signal #7417* CC1 state 0
544 * CC2 state 0
544 * CC3 state 0
544 * CC4 state 0
544 * CC5 state 0
544 DRM: DRM_Process started
544 * CC7 state 0
544 * CC6 state 0
553 Assert Failure in .\cxc1328697_G200_PHONE_KRISTINA\IAR-ARM7\inc\dispdrv_phys_pdi.c(980)
554 SS: State Idle @
554 CallMeter started
555 SMC_MO_1 (65627) state 4
555 SMC_MO_2 (65628) state 4
555 SMC_MT (65629) state 4
555 SMR_MO state 3
555 SMR_MT state 3
555 GDFS_SRV State 1-ClosedAM: MODULE_INIT
558 [sysctrl] Enabling UICC refresh task.
558 R2BA010 prgCXC125978_EU_1_KR
558 [SIM] State Changed: SIM_STATE_NULL, Appl: 0, Ref: 0
566 GDFS: Format version 1
566 GDFS Log[0] <- Phys[0] 120122 bytes left. Erased 1 times
567 GDFS Log[1] <- Phys[1] 98729 bytes left. Erased 1 times
568 GDFS Log[2] <- Phys[2] 112637 bytes left. Erased 1 times
569 GDFS Log[3] <- Phys[3] 120021 bytes left. Erased 1 times
569 GDFS Log[4] <- Phys[4] 123990 bytes left. Erased 1 times
569 GDFS Log[5] <- Phys[5] 125615 bytes left. Erased 1 times
569 GDFS Log[6] <- Phys[6] 131060 bytes left. Erased 1 times
572 GDFS_SRV State 2-Opening
573 CC: speech ver config 2 0 1 15 15
573 CC: TTY mode = 0
573 * CC0 state 0
574 MPH: PacketChannels activated
574 RR Multislot class GPRS = 8
574 RR state 0
574 MS_TYPE = MS_EGSM900_DCS1800_PCS1900
574 MPH:SelectedModeIndex=1
574 MPH_GD_Info.SensitivityLimit_dBm[BAND_GSM900_OR_EGSM900] = -107
575 ETX OK
575 MPH_GD_Info.SensitivityLimit_dBm[BAND_DCS1800] = -107
576 MPH_GD_Info.SensitivityLimit_dBm[BAND_PCS1900] = -107
576 MPH_GD_Info.SensitivityLimit_dBm[BAND_GSM850] = -107
576 MPH_GD_Info.MinNrOfIdentifiedCellsToSkipWeakCells = 0
579 MMM IMEI = 359986-00-822369-0, IMEI_SVN = 22
579 MMM EqPLMN List read from GDFS, nbr=1, 250 2
579 MMM: TVP Probe P_UAS_CAS_PLMN_List Error
579 MMM state 0
579 MMM MM_SIM_DATA_SET_REQ
581 DebugMux[IMEI] Length=8, TypeOfID=2, OddEven=1, Digits: 3 5 9 9 8 6 0 0 8
584 [lockctrl] SimLock : NOT OK, PhoneLock : NOT OK, Sim Active : NOT ACTIVE
585 IrDA_lap_rec.c: IrLAP process ready !
587 IrDA_lmp_rec.c: IrLMP process ready !
587 MMM MS_OperationMode=0
587 CCS: Idle
587 SL: SIGID_INTERVAL_START_MOD_NS_CAS = 3660
588 SL: ProcessID = 10055
588 SL: CFG_DISABLE_SECURITY_HANDLING is NOT! defined
588 SL: DUAL_RAT_SUPPORT is NOT! defined
588 SL state 0
588 SL<-EVENT_SIM_STATE_CHANGED in State 0 from 100ac
588 SL: Not active
588 SL new SIM handle=0
588 Load Module Starter: Hunt for Program Manager failedACM: Starting Application Side.
590 [sysctrl] start-up cause : Accessory
590 [SIM_FILE_UTIL] FCP Cache Size 80
590 SL<-R_REQ_NS_ACTIVATE in State 0 from 1002e
590 MM: state 12
590 MM: TVP Probe P_UAS_CAS_MM_Status Error
591 MMM RH_ACTIVATE_REQ, PLMN = 250 2, SwitchRAT=0
591 RR mph_act_req, 250, 2
591 MPH: EGSM900_DCS1800
591 RR state 1
591 RLC_UL: S S C Lost
591 RH state: GSM Active
591 MMM state 12
591 GMM<-GMM_ATTACH_REQ[sysctrl] System mode changed from SHUTDOWN/INITIATING to WAITING_FOR_UNLOCK
592 [sysctrl] System Start-Up is suspended until SIM locks or SIM is activated
592 [lockctrl] SimLock : NOT OK, PhoneLock : NOT OK, Sim Active : NOT ACTIVE
592 [lockctrl] SimLock : OK, PhoneLock : NOT OK, Sim Active : NOT ACTIVE
592 [lockctrl] SimLock : OK, PhoneLock : OK, Sim Active : NOT ACTIVE
592 [sysctrl] Normal Voltage ind. received from SysPwr
592 SL state 1
592 SL<-MMM_RAT_CHANGE_IND in State 1 from 1004a
592 SL: new RAT = 0
592 SL<-EVENT_SYSCTRL_LOCKCONTROL in State 1 from 1002e
593 MPH CellSelection
593 MPH Take new rxlev measurements
593 RLP: process started
593 L2RCOP: process started
593 RLP: state changed to 'S0_ADMandDetached'
593 L2RCOP: state changed to 'Initial'
597 AT process: Awake and AT your service!
603 ###Downloading DSP for first time after startup of phone!###
605 DSPIF_INT Exception: MPORTIF Soft reset
605 DSPIF_INT Exception: MPORTIF Soft reset
605 [ICC] Reader Voltage:OFF
605 [SIM-RDR] Fi: 1 Di: 1 Div1: 0 Div2: 0
606 [ICC] Reader Voltage:1V8ACM.StartMain: Starting First App. id=1...
610 ACM.StartMain: Start of First App ok.
611 AM: MODULE_INIT_READY
611
611
614 GVI:ReadyDSPIF_INT Exception: MPORTIF Soft reset
614 DSPIF_INT Exception: MPORTIF Soft reset
611 ******************************************
616 * Sony Ericsson Mobile Communications AB *
616 * Copyright 2003 *
616 ******************************************
616 * R2BA010 prgCXC125978_EU_1_KR *
616 ******************************************
616
616
616 AAM: Start initializing persistent data.
617 (OBEX/obex_session.c line: 2224) OBEX Started.
617 RTP_Ctrl started
618 ## DSP VersionIdentity: "Marita Compact DSP midi_pcm_asr CNH1600219_R2L002______ 18Feb2005_13:44:18"
628 [ICC] Reader Voltage:OFF
640 [SIM-RDR] Fi: 1 Di: 1 Div1: 0 Div2: 0
640 [ICC] Reader Voltage:3V
662 [ICC] Reader Voltage:OFF
662 [SIM] WARNING - Destruction of Application Parameters
662 [SIM_FILE_UTIL] Used Cache Records 0
662 [SIM_FILE_UTIL] Max Cache Records 80
662 [SIM] WARNING - Destruction of Card Parameters
662 [SIM] State Changed: SIM_STATE_POWER_OFF, Appl: 0, Ref: 0
662 [lockctrl] SimLock : OK, PhoneLock : OK, Sim Active : NOT ACTIVE
663 SL<-EVENT_SIM_STATE_CHANGED in State 1 from 100ac
663 SL new SIM handle=0AAM: Done initializing persistent data.
732 MMPROT[RTSP]: RTSP Process Started
749
751 MSG: msgmain.c: State 255
751 CBS: cbs_main.c: EVENT_SYSCTRL_LOCKCONTROL rejectedOS: Starting ose_memory_mgr
751 OS: core startup complete!
756 GDFS_Wrapper: **** Up and running ****
756
756 MAPP: OSC accessoryGDFS_Wrapper: GDFSW_RestoreFromFile called.
777 GDFS_WR State 1-Closed
778 GDFS_WR Start check
778 BATT: Battery type is UNKNOWN
783 BATT: Measurements are 2798 mV and -150.0 mA
783 BATT: Compensated VBAT (2882 mV) based remaining capacity is 0.0%
805 TIME LD:ld_time.c Init of RTC failed
806 DRM Init OK
806 DRM_PRS_Process started
1016 GDFS Free Blk 7 Ok
1016 GDFS_WR Check done
1016 GDFS_SRV State 3-Open
1016 GDFS_WR State 2-Open
1024 GDFS_SRV Queue full
1039 GDFS_SRV Queue emptyGDFS_Wrapper: GDFSW_RestoreFromFile finished:ERRORS were found!!!
1071 GDFS_SRV Queue full
1078 MPH: Switch to other mobile mode
1087 HPB: PB_INIT Waiting For Activation
1103 Watchdog: process up and running.
1103 Watchdog: Crash SMS not activated
1105 ***** Investigating Language Availability *****
1110 EST: FS = Available, ROM = Unavailable
1111 ENG: FS = Unavailable, ROM = Available
1111 LAT: FS = Available, ROM = Unavailable
1111 LIT: FS = Available, ROM = Unavailable
1111 POL: FS = Available, ROM = Unavailable
1111 RUS: FS = Available, ROM = Unavailable
1111 UKR: FS = Available, ROM = Unavailable
1111 ***********************************************
1112 Disp_CreateFont: Creating font 0
1112 Disp_CreateFont: Creating font 1
1113 AUC_INFO: AC_SetAcousticProperties, /ifs/settings/acoustic/farfield_play.apf
1115 Disp_CreateFont: Creating font 2
1116 Disp_CreateFont: Creating font 10
1117 Disp_CreateFont: Creating font 11
1118 Disp_CreateFont: Creating font 12
1119 Disp_CreateFont: Creating font 13
1119 Disp_CreateFont: Creating font 15
1119 *** Disp_SetDefaultGlyph: Font 15 failed to set default glyph!
1119 SEMC DISPUTIL Line:1953 OPA_ErrorCode: Unknown ErrorCode
1119 Disp_CreateFont: Creating font 16
1120 Disp_CreateFont: Creating font 17
1120 Disp_CreateFont: Creating font 18
1120 Disp_CreateFont: Creating font 20
1121 Disp_CreateFont: Creating font 31
1121 Disp_CreateFont: Creating font 32
1121 Disp_CreateFont: Creating font 33
1121 Disp_CreateFont: Creating font 34
1122 Disp_CreateFont: Creating font 47
1122 Disp_CreateFont: Creating font 55
1122 Disp_CreateFont: Creating font 54
1128 ***** Investigating Input Features *****
1128 Arabic: NO
1128 China: NO
1128 Hebrew: NO
1128 T9: YES
1128 Greek: NO
1128 Cyrillic: NO
1128 Thai: NO
1128 Icelandic: NO
1128 Ukrainian: NO
1128 Hindi: NO
1128 Bengali: NO
1128 ****************************************
1128 ***** Investigating Input Language Availability *****
1129 Predictive state is: ON
1129 Predictive default (cust) is: ON
1129 ENG: allowed = YES, T9-FS = NO, T9-ROM = YES
1129 POL: allowed = YES, T9-FS = YES, T9-ROM = NO
1129 RUS: allowed = YES, T9-FS = YES, T9-ROM = NO
1130 USE: allowed = YES, T9-FS = NO, T9-ROM = YES
1130 UKR: allowed = YES, T9-FS = NO, T9-ROM = NO
1130 ABC: allowed = YES, T9-FS = NO, T9-ROM = NO
1130 123: allowed = YES, T9-FS = NO, T9-ROM = NO
1130 *** (T9) ENG matches USE
1131 *** Resolve ok (1), keeping ENG
1131 ************************************************** ***
1138 [StandbyBook:53] Created
1143 HPB: PB process started
1146 SL<-REQUEST_VOICECALLVOLUME_SET in State 1 from 100cf
1154 SL<-REQUEST_CURRENTPLMN_STATUS_GET in State 1 from 100df
1159 CMZ Log:
=== Startup with CMZ_Mode_Init ======
1232 ATCS: ATCS Up and running. Waiting for Accessory to be connected
1245 MPH: PCS1900
1246 MPH Take new rxlev measurements
1257 CMZ Log:
DDM started in mode 0xf2:
1264 CMZ Content Revision: R2BA010
1265 [StandbyBook:53] Goto StandbyBook_StandbyPage
1265 [InitBook:54] Created
1265 [InitBook:54] Goto InitBook_StartUp_Page
1265 [InitBook:54] Got focus
1266 ***** Auto language at startup, getting preferred value (4)
1268 [InitBook:54] Goto InitBook_Customization_Page
1341
1341 WAP:Start (process id 0x10089)
1341 WAP: File API Initiated
1342 WAP: created task 0
1343 WAP: fileMkDir(.../stk)
1344 WAP: fileMkDir(.../stk/tmp)
1346 WAP: created task 1
1351 OAS: 0 Profile Roles active
1351 changed to state 0
1351 PBS Process started
1352
1352 PBS: Dispatch PHB_NO_ACCESS
1367 HPB: PB_INIT Activated
1368 HPB: InitContactPbag
1369 HPB: InitGroupPbag
1418 GDFS_SRV Queue empty
1488 MSG: msgmain.c: State 0 changed to state 1
1488 MSG: msgmain.c: EVENT_SIM_STATE_CHANGED accepted
1488 MSG: msgmain.c: SIM_STATE NOT Active
1488 MSG: msgmain.c: EVENT_SIM_STATE_CHANGED accepted
1488 MSG: msgmain.c: SIM_STATE NOT Active
1506 MPH: Switch to other mobile mode
1515 MPH: EGSM900_DCS1800
1765 MPH Take new rxlev measurements
1979 Handle_Shell_Timeout: Time-out from non-existent timer: 4c715cdc - Ignored.
1979 Handle_Shell_Timeout: Time-out from non-existent timer: 4c715cdc - Ignored.
1979 Handle_Shell_Timeout: Time-out from non-existent timer: 4c715cdc - Ignored.
1980 Handle_Shell_Timeout: Time-out from non-existent timer: 4c715cdc - Ignored.
1981 Handle_Shell_Timeout: Time-out from non-existent timer: 4c715cdc - Ignored.
1984 Handle_Shell_Timeout: Time-out from non-existent timer: 4c715cdc - Ignored.
1993 Handle_Shell_Timeout: Time-out from non-existent timer: 4c715cdc - Ignored.
2119 Handle_Shell_Timeout: Time-out from non-existent timer: 4c715cdc - Ignored.
2120 Handle_Shell_Timeout: Time-out from non-existent timer: 4c715cdc - Ignored.
2120 Handle_Shell_Timeout: Time-out from non-existent timer: 4c715cdc - Ignored.
2122 Handle_Shell_Timeout: Time-out from non-existent timer: 4c715cdc - Ignored.
2123 Handle_Shell_Timeout: Time-out from non-existent timer: 4c715cdc - Ignored.
2249 MPH: Switch to other mobile mode
2258 MPH: PCS1900
2258 MPH Take new rxlev measurements
2518 MPH: Switch to other mobile mode
2527 MPH: EGSM900_DCS1800
2728 Handle_Shell_Timeout: Time-out from non-existent timer: 4c715cdc - Ignored.
2777 MPH Take new rxlev measurements
3260 MPH: Switch to other mobile mode
3270 MPH: PCS1900
3270 MPH Take new rxlev measurements
3530 MPH: Switch to other mobile mode
3539 MPH: EGSM900_DCS1800
3789 MPH Take new rxlev measurements
4272 MPH: Switch to other mobile mode
4282 MPH: PCS1900
4282 MPH Take new rxlev measurements
4541 MPH: Switch to other mobile mode
4551 MPH: EGSM900_DCS1800
4801 MPH Take new rxlev measurements
5284 MPH: Switch to other mobile mode
5293 MPH: PCS1900
5293 MPH Take new rxlev measurements
5552 MPH: Switch to other mobile mode
5561 MPH: EGSM900_DCS1800
5811 MPH Take new rxlev measurements
5843 [sysctrl] Normal Voltage ind. received from SysPwr
6295 MPH: Switch to other mobile mode
6304 MPH: PCS1900
6304 MPH Take new rxlev measurements
6564 MPH: Switch to other mobile mode
6567 GDFS_SRV Queue full
6573 MPH: EGSM900_DCS1800
6617 GDFS_SRV NoWrites 500 Max Queue 2635
6641 GDFS_SRV Queue empty
6772 SL<-REQUEST_PREFERREDMO_SMS_DOMAIN_SET in State 1 from 100cd
6772 SL<-REQUEST_MS_OPERATIONMODE_SET in State 1 from 100cd
6772 SL<-REQUEST_SEARCHMODE_SET in State 1 from 100cd
6824 MPH Take new rxlev measurements
7062 FSFLASH: Formatting flash block 25
7308 MPH: Switch to other mobile mode
7317 MPH: PCS1900
7317 MPH Take new rxlev measurements
7576 MPH: Switch to other mobile mode
7585 MPH: EGSM900_DCS1800
7835 MPH Take new rxlev measurements
8206 FSFLASH: Formatting flash block 26
8251 CBS: cbs_main.c: CBS_ALIVE_TIMER_IND accepted
8319 MPH: Switch to other mobile mode
8328 MPH: PCS1900
8328 MPH Take new rxlev measurements
8538 BATT: Measurements are 3744 mV and -49.7 mA
8538 BATT: Compensated VBAT (3805 mV) based remaining capacity is 49.1%
8538 BATT: Average remaining capacity is 49.1%
8588 MPH: Switch to other mobile mode
8597 MPH: EGSM900_DCS1800
8847 MPH Take new rxlev measurements
9286 Themes_bk.c Themes_SetDefaultTheme() - Setting new theme file: Lunarspots.thm
9294 Themes_bk.c Themes_SetDefaultTheme() - Success to create link
9314 CMZ Log: Ready
9320 CMZ Log:
CMZ started in mode 0xe1:
9331 MPH: Switch to other mobile mode
9333 CMZ CDA Revision: R2A
9340 MPH: PCS1900
9340 MPH Take new rxlev measurements
9363 FSFLASH: Formatting flash block 27
9600 MPH: Switch to other mobile mode
9609 MPH: EGSM900_DCS1800
9859 MPH Take new rxlev measurements
10343 MPH: Switch to other mobile mode
10352 MPH: PCS1900
10352 MPH Take new rxlev measurements
10409 CMZ Log: Ready
10416 CMZ Log:
10423 CMZ Log: Success - 0 error(s), 0 warning(s)
10439 FS: 1 commit-at-close files open, can't sync the file system.
10459 FSFLASH: Formatting flash block 28
10612 MPH: Switch to other mobile mode
10621 MPH: EGSM900_DCS1800
10871 MPH Take new rxlev measurements
11045 ***** Auto language at startup, getting preferred value (4)
11052 Tararchive.c TARArchiveOpenFile(): Failed to open file
11052 Tararchive.c
11052 /tpa/preset/custom/DESKTOP_HOOK_1.itm
11053 errno 202
11071 Tararchive.c TARArchiveOpenFile(): Failed to open file
11071 Tararchive.c
11071 /tpa/preset/custom/DESKTOP_HOOK_3.itm
11072 errno 202
11074 Tararchive.c TARArchiveOpenFile(): Failed to open file
11074 Tararchive.c
11074 /tpa/preset/custom/NOT_YET_DECIDED.itm
11075 errno 202
11077 Tararchive.c TARArchiveOpenFile(): Failed to open file
11077 Tararchive.c
11077 /tpa/preset/custom/NOT_YET_DECIDED.itm
11078 errno 202
11082 Tararchive.c TARArchiveOpenFile(): Failed to open file
11082 Tararchive.c
11082 /tpa/preset/custom/VOICE_NOTE_HOOK.itm
11083 errno 202
11085 Tararchive.c TARArchiveOpenFile(): Failed to open file
11085 Tararchive.c
11085 /tpa/preset/custom/WIRELESS_VILLAGE_HOOK.itm
11086 errno 202
11088 Tararchive.c TARArchiveOpenFile(): Failed to open file
11088 Tararchive.c
11088 /tpa/preset/custom/CALL_LIST_HOOK.itm
11090 errno 202
11092 Tararchive.c TARArchiveOpenFile(): Failed to open file
11092 Tararchive.c
11092 /tpa/preset/custom/GAMES_HOOK_1.itm
11093 errno 202
11095 Tararchive.c TARArchiveOpenFile(): Failed to open file
11095 Tararchive.c
11095 /tpa/preset/custom/GAMES_HOOK_2.itm
11096 errno 202
11105 Timer unx. msg [28673,6] from 98506
11168 Tararchive.c TARArchiveOpenFile(): Failed to open file
11168 Tararchive.c
11168 /tpa/preset/custom/FM_PICTURES_HOOK_1.itm
11170 errno 202
11171 Tararchive.c TARArchiveOpenFile(): Failed to open file
11171 Tararchive.c
11171 /tpa/preset/custom/FM_PICTURES_HOOK_2.itm
11173 errno 202
11209 Tararchive.c TARArchiveOpenFile(): Failed to open file
11209 Tararchive.c
11209 /tpa/preset/custom/SETT_RINGTONE_HOOK_1.itm
11211 errno 202
11212 Tararchive.c TARArchiveOpenFile(): Failed to open file
11212 Tararchive.c
11212 /tpa/preset/custom/SETT_RINGTONE_HOOK_2.itm
11214 errno 202
11246 Tararchive.c TARArchiveOpenFile(): Failed to open file
11246 Tararchive.c
11246 /tpa/preset/custom/FM_SOUNDS_HOOK_1.itm
11248 errno 202
11249 Tararchive.c TARArchiveOpenFile(): Failed to open file
11249 Tararchive.c
11249 /tpa/preset/custom/FM_SOUNDS_HOOK_2.itm
11251 errno 202
11285 Tararchive.c TARArchiveOpenFile(): Failed to open file
11285 Tararchive.c
11285 /tpa/preset/custom/FM_VIDEOS_HOOK_1.itm
11287 errno 202
11288 Tararchive.c TARArchiveOpenFile(): Failed to open file
11288 Tararchive.c
11289 /tpa/preset/custom/FM_VIDEOS_HOOK_2.itm
11290 errno 202
11321 Tararchive.c TARArchiveOpenFile(): Failed to open file
11321 Tararchive.c
11321 /tpa/preset/custom/FM_THEMES_HOOK_1.itm
11322 errno 202
11324 Tararchive.c TARArchiveOpenFile(): Failed to open file
11324 Tararchive.c
11324 /tpa/preset/custom/FM_THEMES_HOOK_2.itm
11325 errno 202
11355 MPH: Switch to other mobile mode
11359 Tararchive.c TARArchiveOpenFile(): Failed to open file
11359 Tararchive.c
11359 /tpa/preset/custom/MESSAGES_HOOK_1.itm
11360 errno 202
11362 Tararchive.c TARArchiveOpenFile(): Failed to open file
11362 Tararchive.c
11362 /tpa/preset/custom/MESSAGES_HOOK_2.itm
11363 errno 202
11364 MPH: PCS1900
11364 MPH Take new rxlev measurements
11366 Tararchive.c TARArchiveOpenFile(): Failed to open file
11366 Tararchive.c
11366 /tpa/preset/custom/HOME_SCREEN_HOOK_1.itm
11367 errno 202
11369 Tararchive.c TARArchiveOpenFile(): Failed to open file
11369 Tararchive.c
11369 /tpa/preset/custom/HOME_SCREEN_HOOK_2.itm
11371 errno 202
11373 Tararchive.c TARArchiveOpenFile(): Failed to open file
11373 Tararchive.c
11373 /tpa/preset/custom/HOME_SCREEN_HOOK_3.itm
11374 errno 202
11376 Tararchive.c TARArchiveOpenFile(): Failed to open file
11376 Tararchive.c
11376 /tpa/preset/custom/HOME_SCREEN_HOOK_4.itm
11376 errno 202
11379 Tararchive.c TARArchiveOpenFile(): Failed to open file
11379 Tararchive.c
11379 /tpa/preset/custom/HOME_SCREEN_HOOK_5.itm
11380 errno 202
11382 Tararchive.c TARArchiveOpenFile(): Failed to open file
11383 Tararchive.c
11383 /tpa/preset/custom/HOME_SCREEN_CONTENT_HOOK.itm
11383 errno 202
11386 Tararchive.c TARArchiveOpenFile(): Failed to open file
11386 Tararchive.c
11386 /tpa/preset/custom/SETT_WALLPAPER_HOOK_1.itm
11387 errno 202
11389 Tararchive.c TARArchiveOpenFile(): Failed to open file
11389 Tararchive.c
11390 /tpa/preset/custom/SETT_WALLPAPER_HOOK_2.itm
11390 errno 202
11394 Tararchive.c TARArchiveOpenFile(): Failed to open file
11394 Tararchive.c
11394 /tpa/preset/custom/SETT_STARTSHOW_HOOK_1.itm
11396 errno 202
11397 Tararchive.c TARArchiveOpenFile(): Failed to open file
11398 Tararchive.c
11398 /tpa/preset/custom/SETT_STARTSHOW_HOOK_2.itm
11399 errno 202
11402 Tararchive.c TARArchiveOpenFile(): Failed to open file
11402 Tararchive.c
11402 /tpa/preset/custom/SETT_SCREENSAVER_HOOK_1.itm
11404 errno 202
11406 Tararchive.c TARArchiveOpenFile(): Failed to open file
11406 Tararchive.c
11406 /tpa/preset/custom/SETT_SCREENSAVER_HOOK_2.itm
11408 errno 202
11411 Tararchive.c TARArchiveOpenFile(): Failed to open file
11411 Tararchive.c
11411 /tpa/preset/custom/ORG_APPLICATIONS_HOOK_1.itm
11413 errno 202
11414 Tararchive.c TARArchiveOpenFile(): Failed to open file
11414 Tararchive.c
11414 /tpa/preset/custom/ORG_APPLICATIONS_HOOK_2.itm
11416 errno 202
11419 Tararchive.c TARArchiveOpenFile(): Failed to open file
11419 Tararchive.c
11419 /tpa/preset/custom/MEDIA_PLAYER_HOOK_1.itm
11421 errno 202
11422 Tararchive.c TARArchiveOpenFile(): Failed to open file
11423 Tararchive.c
11423 /tpa/preset/custom/MEDIA_PLAYER_HOOK_2.itm
11424 errno 202
11427 Tararchive.c TARArchiveOpenFile(): Failed to open file
11427 Tararchive.c
11428 /tpa/preset/custom/ENTERTAINMENT_HOOK_1.itm
11429 errno 202
11431 Tararchive.c TARArchiveOpenFile(): Failed to open file
11431 Tararchive.c
11431 /tpa/preset/custom/ENTERTAINMENT_HOOK_2.itm
11432 errno 202
11434 Tararchive.c TARArchiveOpenFile(): Failed to open file
11434 Tararchive.c
11434 /tpa/preset/custom/ENTERTAINMENT_HOOK_3.itm
11436 errno 202
11468 Tararchive.c TARArchiveOpenFile(): Failed to open file
11468 Tararchive.c
11468 /tpa/preset/custom/RIGHT_SOFTKEY_HOOK.itm
11470 errno 202
11471 Tararchive.c TARArchiveOpenFile(): Failed to open file
11471 Tararchive.c
11472 /tpa/preset/custom/OPERATOR_KEY_HOOK.itm
11473 errno 202
11485 [InitBook:54] Goto InitBook_StartUp_Page
11489 [CallManagerBook:55] Created
11491 [CallManagerBook:55] Goto Manager_Idle_Page
11492 [InitBook:54] Goto InitBook_Started_Page
11492 [SIMCardAuthentication_Book:56] Created
11493 [SIMCardAuthentication_Book:56] Goto SimAuth_InsertSIM_Page
11493 [SimError_Book:57] Created
11493 [InitBook:54] Lost focus
11493 [SimError_Book:57] Got focus
11493 [SimError_Book:57] Goto SimError_ShowMessage_Page
11553 AUC: Open Audio: ID: 1. Frequency: 3. Prio: 1 Channels: [0,1,0,1]
11553 AUC: Open Audio: Open Channels 1, Freq: 3
11558 DSPIF_INT Exception: MPORTIF Soft reset
11558 DSPIF_INT Exception: MPORTIF Soft reset
11560 DSPIF_INT Exception: MPORTIF Soft reset
11560 DSPIF_INT Exception: MPORTIF Soft reset
11568 DSPIF_INT Exception: MPORTIF Soft reset
11568 DSPIF_INT Exception: MPORTIF Soft reset
11572 ## DSP VersionIdentity: "Marita Compact DSP midi_pcm_asr CNH1600219_R2L002______ 18Feb2005_13:44:18"
11587 *** CreateTextFeedback is obsolete. ***
File: .\cxc125978_EU_1_KR\IAR-ARM7\src\simerror_bk.c
11588 SL<-REQUEST_TTY_MODE_SET in State 1 from 100d4
11588 SL: SIM not ok yet
11589 ***** Calling IAC_ServerASC_SetVolume *****
11589 ***** RingVolume = 5 ****
11589 ***** SUCCESS *****
11620 [StandbyBook:53] Goto StandbyBook_StandbyPage
11621
11621 SL<-REQUEST_RXSIGNALPARAMS_GET in State 1 from 100d0
11622 INTERNAL ERROR CNetworkManager_imp.c(1249): 0x00000007
11624 MPH: Switch to other mobile mode
11633 MPH: EGSM900_DCS1800
11747 AUC: Close Audio: ID: 1. Frequency: 3. Channels: [0,1,0,1]. SendEvent: 0
11752 AUC: Close Audio: Open Channels 0, Freq: 0
11996 Crypto-capable module loaded as default.
14133 MPH Take new rxlev measurements
14618 MPH: Switch to other mobile mode
14627 MPH: PCS1900
14628 MPH Take new rxlev measurements
14887 MPH: Switch to other mobile mode
14897 MPH: EGSM900_DCS1800
15751 CBS: cbs_main.c: CBS_ALIVE_TIMER_IND accepted
15777 FSFLASH: Formatting flash block 29
16193 BATT: Measurements are 3739 mV and -44.9 mA
16194 BATT: Compensated VBAT (3799 mV) based remaining capacity is 47.5%
16194 BATT: Average remaining capacity is 48.3%
16527 FSFLASH: Formatting flash block 30
17277 FSFLASH: Formatting flash block 31
17398 MPH Take new rxlev measurements
17883 MPH: Switch to other mobile mode
17892 MPH: PCS1900
17893 MPH Take new rxlev measurements
18027 FSFLASH: Formatting flash block 32
18152 MPH: Switch to other mobile mode
18162 MPH: EGSM900_DCS1800
18777 FSFLASH: Formatting flash block 33
19527 FSFLASH: Formatting flash block 34
20277 FSFLASH: Formatting flash block 35
20662 MPH Take new rxlev measurements
21027 FSFLASH: Formatting flash block 36
21145 MPH: Switch to other mobile mode
21155 MPH: PCS1900
21155 MPH Take new rxlev measurements
21414 MPH: Switch to other mobile mode
21424 MPH: EGSM900_DCS1800
21777 FSFLASH: Formatting flash block 37
22527 FSFLASH: Formatting flash block 38
23251 CBS: cbs_main.c: CBS_ALIVE_TIMER_IND accepted
23277 FSFLASH: Formatting flash block 39
23693 BATT: Measurements are 3748 mV and -33.4 mA
23694 BATT: Compensated VBAT (3805 mV) based remaining capacity is 49.1%
23694 BATT: Average remaining capacity is 48.5%
23924 MPH Take new rxlev measurements
24027 FSFLASH: Formatting flash block 40
24409 MPH: Switch to other mobile mode
24418 MPH: PCS1900
24418 MPH Take new rxlev measurements
24678 MPH: Switch to other mobile mode
24687 MPH: EGSM900_DCS1800
24777 FSFLASH: Formatting flash block 41
25527 FSFLASH: Formatting flash block 4227027 FSFLASH: Formatting flash block 44
27188 MPH Take new rxlev measurements
27194 BATT: Measurements are 3806 mV and -26.5 mA
27194 BATT: Charge current (-26.5 mA) based remaining capacity is 100.0%
27194 BATT: Average remaining capacity is 61.4%
27444 BATT: Measurements are 3763 mV and -51.0 mA
27444 BATT: Compensated VBAT (3638 mV) based remaining capacity is 6.7%
27444 BATT: Average remaining capacity is 50.4%
27671 MPH: Switch to other mobile mode
27680 MPH: PCS1900
27680 MPH Take new rxlev measurements
27694 BATT: Measurements are 3752 mV and -45.0 mA
27694 BATT: Compensated VBAT (3627 mV) based remaining capacity is 5.8%
27694 BATT: Average remaining capacity is 43.0%
27777 FSFLASH: Formatting flash block 45
27940 MPH: Switch to other mobile mode
27944 BATT: Measurements are 3763 mV and -51.0 mA
27944 BATT: Compensated VBAT (3638 mV) based remaining capacity is 6.7%
27944 BATT: Average remaining capacity is 37.8%
27949 MPH: EGSM900_DCS1800
28194 BATT: Measurements are 3763 mV and -34.0 mA
28194 BATT: Compensated VBAT (3638 mV) based remaining capacity is 6.7%
28194 BATT: Average remaining capacity is 33.9%
28444 BATT: Measurements are 3763 mV and -34.0 mA
28444 BATT: Compensated VBAT (3638 mV) based remaining capacity is 6.7%
28444 BATT: Average remaining capacity is 30.9%
28527 FSFLASH: Formatting flash block 46
28694 BATT: Measurements are 3763 mV and -28.0 mA
28694 BATT: Compensated VBAT (3638 mV) based remaining capacity is 6.7%
28694 BATT: Average remaining capacity is 28.5%
28944 BATT: Measurements are 3763 mV and -34.0 mA
28944 BATT: Compensated VBAT (3638 mV) based remaining capacity is 6.7%
28944 BATT: Average remaining capacity is 26.5%
29194 BATT: Measurements are 3763 mV and -28.0 mA
29194 BATT: Compensated VBAT (3638 mV) based remaining capacity is 6.7%
29194 BATT: Average remaining capacity is 24.8%
29277 FSFLASH: Formatting flash block 47
29444 BATT: Measurements are 3763 mV and -34.0 mA
29444 BATT: Compensated VBAT (3638 mV) based remaining capacity is 6.7%
29444 BATT: Average remaining capacity is 23.4%
29694 BATT: Measurements are 3763 mV and -34.0 mA
29694 BATT: Compensated VBAT (3638 mV) based remaining capacity is 6.7%
29694 BATT: Average remaining capacity is 22.2%
29944 BATT: Measurements are 3763 mV and -28.0 mA
29944 BATT: Compensated VBAT (3638 mV) based remaining capacity is 6.7%
29944 BATT: Average remaining capacity is 21.2%
30027 FSFLASH: Formatting flash block 48
30194 BATT: Measurements are 3763 mV and -28.0 mA
30194 BATT: Compensated VBAT (3638 mV) based remaining capacity is 6.7%
30194 BATT: Average remaining capacity is 20.3%
30444 BATT: Measurements are 3763 mV and -34.0 mA
30444 BATT: Compensated VBAT (3638 mV) based remaining capacity is 6.7%
30444 BATT: Average remaining capacity is 19.5%
30449 MPH Take new rxlev measurements
30694 BATT: Measurements are 3763 mV and -51.0 mA
30694 BATT: Compensated VBAT (3638 mV) based remaining capacity is 6.7%
30694 BATT: Average remaining capacity is 18.8%
30751 CBS: cbs_main.c: CBS_ALIVE_TIMER_IND accepted
30777 FSFLASH: Formatting flash block 49
30931 MPH: Switch to other mobile mode
30941 MPH: PCS1900
30941 MPH Take new rxlev measurements
30944 BATT: Measurements are 3763 mV and -45.0 mA
30944 BATT: Compensated VBAT (3638 mV) based remaining capacity is 6.7%
30944 BATT: Average remaining capacity is 18.1%
31194 BATT: Measurements are 3752 mV and -56.0 mA
31194 BATT: Compensated VBAT (3627 mV) based remaining capacity is 5.8%
31194 BATT: Average remaining capacity is 17.5%
31200 MPH: Switch to other mobile mode
31210 MPH: EGSM900_DCS1800
31444 BATT: Measurements are 3752 mV and -28.0 mA
31444 BATT: Compensated VBAT (3627 mV) based remaining capacity is 5.8%
31444 BATT: Average remaining capacity is 15.3%
31527 FSFLASH: Formatting flash block 50
31694 BATT: Measurements are 3763 mV and -28.0 mA
31694 BATT: Compensated VBAT (3638 mV) based remaining capacity is 6.7%
31694 BATT: Average remaining capacity is 13.3%
31944 BATT: Measurements are 3763 mV and -39.0 mA
31944 BATT: Compensated VBAT (3638 mV) based remaining capacity is 6.7%
31944 BATT: Average remaining capacity is 11.2%
32194 BATT: Measurements are 3763 mV and -28.0 mA
32194 BATT: Compensated VBAT (3638 mV) based remaining capacity is 6.7%
32194 BATT: Average remaining capacity is 6.5%
32277 FSFLASH: Formatting flash block 51
32444 BATT: Measurements are 3763 mV and -22.0 mA
32444 BATT: Compensated VBAT (3638 mV) based remaining capacity is 6.7%
32444 BATT: Average remaining capacity is 6.5%
32694 BATT: Measurements are 3763 mV and -39.0 mA
32694 BATT: Compensated VBAT (3638 mV) based remaining capacity is 6.7%
32694 BATT: Average remaining capacity is 6.6%
32944 BATT: Measurements are 3763 mV and -28.0 mA
32944 BATT: Compensated VBAT (3638 mV) based remaining capacity is 6.7%
32944 BATT: Average remaining capacity is 6.6%
33027 FSFLASH: Formatting flash block 52
33194 BATT: Measurements are 3763 mV and -28.0 mA
33194 BATT: Compensated VBAT (3638 mV) based remaining capacity is 6.7%
33194 BATT: Average remaining capacity is 6.6%
33444 BATT: Measurements are 3763 mV and -34.0 mA
33444 BATT: Compensated VBAT (3638 mV) based remaining capacity is 6.7%
33444 BATT: Average remaining capacity is 6.6%
33694 BATT: Measurements are 3763 mV and -34.0 mA
33694 BATT: Compensated VBAT (3638 mV) based remaining capacity is 6.7%
33694 BATT: Average remaining capacity is 6.6%
33710 MPH Take new rxlev measurements
33777 FSFLASH: Formatting flash block 53
33944 BATT: Measurements are 3763 mV and -39.0 mA
33944 BATT: Compensated VBAT (3638 mV) based remaining capacity is 6.7%
33944 BATT: Average remaining capacity is 6.6%
34194 BATT: Measurements are 3752 mV and -56.0 mA
34194 BATT: Compensated VBAT (3627 mV) based remaining capacity is 5.8%
34195 MPH: Switch to other mobile mode
34195 BATT: Average remaining capacity is 6.5%
34204 MPH: PCS1900
34204 MPH Take new rxlev measurements
34444 BATT: Measurements are 3752 mV and -51.0 mA
34444 BATT: Compensated VBAT (3627 mV) based remaining capacity is 5.8%
34444 BATT: Average remaining capacity is 6.5%
34464 MPH: Switch to other mobile mode
34473 MPH: EGSM900_DCS1800
34527 FSFLASH: Formatting flash block 54
34694 BATT: Measurements are 3763 mV and -28.0 mA
34694 BATT: Compensated VBAT (3638 mV) based remaining capacity is 6.7%
34694 BATT: Average remaining capacity is 6.5%
34944 BATT: Measurements are 3763 mV and -39.0 mA
34944 BATT: Compensated VBAT (3638 mV) based remaining capacity is 6.7%
34944 BATT: Average remaining capacity is 6.5%
35194 BATT: Measurements are 3763 mV and -28.0 mA
35194 BATT: Compensated VBAT (3638 mV) based remaining capacity is 6.7%
35194 BATT: Average remaining capacity is 6.5%
35277 FSFLASH: Formatting flash block 55
35444 BATT: Measurements are 3763 mV and -28.0 mA
35444 BATT: Compensated VBAT (3638 mV) based remaining capacity is 6.7%
35444 BATT: Average remaining capacity is 6.5%
35694 BATT: Measurements are 3763 mV and -34.0 mA
35694 BATT: Compensated VBAT (3638 mV) based remaining capacity is 6.7%
35694 BATT: Average remaining capacity is 6.5%
35944 BATT: Measurements are 3763 mV and -28.0 mA
35944 BATT: Compensated VBAT (3638 mV) based remaining capacity is 6.7%
35944 BATT: Average remaining capacity is 6.5%
36027 FSFLASH: Formatting flash block 56
36194 BATT: Measurements are 3763 mV and -34.0 mA
36194 BATT: Compensated VBAT (3638 mV) based remaining capacity is 6.7%
36194 BATT: Average remaining capacity is 6.5%
36444 BATT: Measurements are 3763 mV and -34.0 mA
36444 BATT: Compensated VBAT (3638 mV) based remaining capacity is 6.7%
36444 BATT: Average remaining capacity is 6.6%
36694 BATT: Measurements are 3763 mV and -28.0 mA
36694 BATT: Compensated VBAT (3638 mV) based remaining capacity is 6.7%
36694 BATT: Average remaining capacity is 6.6%
36777 FSFLASH: Formatting flash block 57
36944 BATT: Measurements are 3763 mV and -28.0 mA
36944 BATT: Compensated VBAT (3638 mV) based remaining capacity is 6.7%
36944 BATT: Average remaining capacity is 6.6%
36974 MPH Take new rxlev measurements
37194 BATT: Measurements are 3763 mV and -51.0 mA
37194 BATT: Compensated VBAT (3638 mV) based remaining capacity is 6.7%
37194 BATT: Average remaining capacity is 6.6%
37444 BATT: Measurements are 3752 mV and -51.0 mA
37444 BATT: Compensated VBAT (3627 mV) based remaining capacity is 5.8%
37444 BATT: Average remaining capacity is 6.5%
37457 MPH: Switch to other mobile mode
37466 MPH: PCS1900
37467 MPH Take new rxlev measurements
37527 FSFLASH: Formatting flash block 58
37694 BATT: Measurements are 3763 mV and -45.0 mA
37694 BATT: Compensated VBAT (3638 mV) based remaining capacity is 6.7%
37694 BATT: Average remaining capacity is 6.5%
37726 MPH: Switch to other mobile mode
37735 MPH: EGSM900_DCS1800
37944 BATT: Measurements are 3752 mV and -39.0 mA
37944 BATT: Compensated VBAT (3627 mV) based remaining capacity is 5.8%
37944 BATT: Average remaining capacity is 6.5%
38194 BATT: Measurements are 3763 mV and -34.0 mA
38194 BATT: Compensated VBAT (3638 mV) based remaining capacity is 6.7%
38194 BATT: Average remaining capacity is 6.5%
38253 CBS: cbs_main.c: CBS_ALIVE_TIMER_IND accepted
38277 FSFLASH: Formatting flash block 59
38444 BATT: Measurements are 3763 mV and -28.0 mA
38444 BATT: Compensated VBAT (3638 mV) based remaining capacity is 6.7%
38444 BATT: Average remaining capacity is 6.5%
38694 BATT: Measurements are 3763 mV and -34.0 mA
38694 BATT: Compensated VBAT (3638 mV) based remaining capacity is 6.7%
38694 BATT: Average remaining capacity is 6.5%
38944 BATT: Measurements are 3763 mV and -28.0 mA
38944 BATT: Compensated VBAT (3638 mV) based remaining capacity is 6.7%
38944 BATT: Average remaining capacity is 6.5%

[Arni]

а хез. принесли - не заряжается. а там около стекляшки флюсом корявым все залито и на соплях запаяно было, поэтому сразу и переделывал.


Это извините за прямоту просто безответственно. Начинать чинить телефон не посмотрев как он себя ведет полагаясь на слова клиента? Я как-то очень давно, долго объяснял клиенту, почему в Ericsson 2618 из за РФ (Паучок) процессора не заряжается телефон.


Вы могли бы в качестве эксперимента, дабы исключить 100% вероятности плохо припаянной стекляшки, или её повреждения, поставить перемычку между конденсаторами С2400 и C2620? Если все будет так же, то будем думать дальше ...

[alfv]

Помню , был случай , что нормальный заряд шел только с перемычкой . Со стеклом заряжаться не хотел . Это был или K700 или K300. Тело было после воды .

[Viktor001]

BATT: Measurements are 3763 mV and -28.0 mA
Это ненормально, что ток со знаком "минус". Получается, что телефон не заряжает, а наоборот разряжает АКБ. Но почему он не хочет заряжать, в логе не показывает.Так что придётся самому искать.
Контролер питания проверить бы. Вдруг, те что брал с разборки, попались убитые по среднему контакту.
Или всунуть вместо ключа v2610, Самсунговскую LTH7. Она полностью автоматическая, и пускай заряжает.

[Layder]

с перемычкой не заряжается, с другой батареей тоже, с третим контроллером тоже, с замененым разъемом батареи тоже, с другой флешкой - тоже.
менять RF процессор? :D

[vth]

Ну стоит проверить терморезистор r2324, и верхнее плечо r2425.
Только не нашел я на плате ни того, ни другого. Может вам повезёт больше.

[Layder]

они на верхней стороне над джойстиком стоят.
вот телефон!
мало того, что терморезистор 2324 был плохо припаян, мало того, что r2524 второй стороной коротил на землю через пятак незапаяного конденсатора рядом с ним, то после того, как это восстановил, ВСЕ РАВНО тоже самое, что и было описано в первом посте!!!

[alibom]

После стольких мучений! надо сделать телефон а иначе вы не Лидер.
Шутка конечно!

[Layder]

После стольких мучений! надо сделать телефон а иначе вы не Лидер.
Шутка конечно!
правильно читать Лэйдер, как я писал уже где-то, это игра слов Layer-Lider
а, вообще, я уже нашел на него рабочую плату :trud: