COM3 [VCP0] selected
module  v4.01
Device: _Autodetect MT6228-6268 NAND
Checking data, wait...
Action: write flash NAND
write: Firmware
aleck_recalculated.B4M.bin
skip: Customization/Language Pack
skip: Customization
skip: Eeprom/ffs
nfi area detection...
nfi scat area detected (3 areas)
nfi area detection (3 cores) finished: Ok
interface: BROM_DLL_v3.1016.00
Connect...
Phone should be Switched OFF !
Press and HOLD Power button now !
Connecting...
Booting...
Release Power button now !
bootcode current/expected: 3.2/3.2
CPU: 6235:8C00:8A00
status: FF
bbchip bl ver: FE
NOR flash chip: not installed
NAND flash id[0018]: 00AD:007900A50000 [HYNIX] HY27XA081G1M
chip size: 128Mb
page/spare size: 0200/0010
pages per block: 0020
bits i/o: 08
address cycles: 04
internal RAM size: 00010000
external RAM: absent
done
Set baudrate (460800)...
done
interesting cpu type found: 6235:8C00:8A00
ram test...
testing 32bit...
32bit ram test passed
testing 16bit...
16bit ram test passed
ram test passed
===>  detect existing firmware structure...
detect ffs...
ffs offset/size: 03000000/05000000
firmware size: 48Mb
ffs size: 80Mb
detect sec ro...
detect custom parameters...
detect project-id...
project-id: EM941_MP_F1_IT_NGM_22_V15
detect NAND info...
number of areas/bytes to read: 1:00034000
reading (HW_STORAGE_NAND NUTL_READ_PAGE_ONLY)...
nfi area detection...
bootloader version: TINNO35_09A_BOOTLOADER_V005_MT6235B_EM941_MP_F1_IT_NGM_22_V15.bi
warning: id-page1 area is invalid
nfi area detection (0 cores) finished: failed
TCL-ID detection...
TCL-ID detection done
startup code area #1 detection...
number of areas/bytes to read: 1:00004000
reading (HW_STORAGE_NAND NUTL_READ_PAGE_ONLY)...
number of areas/bytes to read: 1:00004000
reading (HW_STORAGE_NAND NUTL_READ_PAGE_ONLY)...
startup code area #1 is invalid
startup code area #1 detection done
rom info ver: 07
sw version: TINNO35_09A_PCB01_GPRS_MT6235B_S01.EM941_MP_F1_IT_NGM_22_V15.BIN
project-id: EM941_MP_F1_IT_NGM_22_V15, 781A1982
code offset: 00000000
ffs offset/size [01]: 03000000/05000000
rom info structure: [protected] type (07), 1 record(s)
TCL-ID is absent
===>  done
nfi area detection...
nfi scat area detected (3 areas)
nfi area detection (3 cores) finished: Ok
startup code area #1 check...
factory firmware detected: TINNO35_09A_PCB01_GPRS_MT6235B_S01.EM941_MP_F1_IT_NGM_22_V15.BIN
====================
New firmware found (v.4.01, database date: 19.08.2011): 
TINNO35_09A_PCB01_GPRS_MT6235B_S01.EM941_MP_F1_IT_NGM_22_V15.BIN

This firmware is missing in support area. If this phone is good and working:

- download latest software from support area and try again, probably this firmware already supported in latest software
- make "Read full flash" operation
- send flash backup files to support: [email protected] or upload files to http://rapidshare.com or http://4shared.com
- include in your e-mail full text from phone back label (phone name etc.)
====================
startup code area #1 calculation...
startup code area #1 fixed
number of cores: 3
loading files...
number of areas: 3
done
write...
write bootloader...
.
.
.
.
write core...
error: can not write flash (31): 0FAF:S_FT_NFB_DOWNLOAD_CODE_FAIL
error: last error: 0FAF:S_FT_NFB_DOWNLOAD_CODE_FAIL
Disconnect...
done
Finished, time used: 8 min 2 sec
Remove/Install battery now !